Machine Accessories GuidePro Woodpeckers Saw Gauge Incra Miter Channel Works with INCRA Miter Sliders and INCRA Miter Gauges or any standard 3/8" by 3/4" miter bar. T-Slot design helps with hold down capability and they are made of hard anodized aluminum for durability. Mounts easily with pre-drilled holes and included fasteners. Cut a 1-1/8" wide by 1/2" deep groove in your application to fit the INCRA T-Slot Miter Channel. When installed, the Miter Channel should sit slightly below the surface of the table. Attach using the supplied fasteners. 32" INCRA MITER CHANNEL IN00032 ...$16.95 48" INCRA MITER CHANNEL IN00048 ...$22.95 GuidePRO is the ideal accessory for all band saw owners. Whether re-sawing dressed lumber or rougher pieces, the GuidePRO, with its flexible silicon feather, will maintain constant pressure between the work piece and the fence helping ensure the squarest cut possible. Just slide the GuidePRO into the miter slot, rotate it clockwise until it stops and push the GuidePRO against the work piece and fence with desired pressure, then press down the locking lever to secure the work piece. Be sure to keep the feather near the leading edge of the work for the cleanest cut. The GuidePRO Extension adds 4" of height to the GuidePRO and comes with a 10" feather. The GuidePRO Anchor Bar is used to adapt the GuidePRO to use on a router table or table saw. GUIDEPRO BAND SAW GUIDE BP06270 .......................................................$77.99 EXTENSION BP06287 ...................$19.99 3/4" ANCHOR BAR BP06294....................$24.99 Even if you spend hundreds or thousands of dollars on a table saw, a super smooth, burn free cut is not guaranteed. Even the best saws need to have the blade and fence properly aligned to the miter slot. Tape measures and straight edges will get close, but won't allow you to get the best from your blade and saw. The Woodpeckers Saw Gauge makes the task faster, easier and much more accurate. Simply take the gauge out of the box, no assembly required, and drop it in the miter slot. By sliding the gauge up and down the blade or fence, you'll know exactly which way to make the adjustment. SAW GAUGE PK36008 ............................$89.99 Double Ended Featherboard The Double Ended Feather-board is made of high impact poly styrene. One side of the featherboard has 1/8" fingers for light to medium pressure while the opposite side has 3/16" fingers which help with larger items that require medium to heavy pressure. It is made to be used with the standard 3/4" x 3/8" miter slot but can also be mounted in a vertical position. DOUBLE ENDED FEATHERBOARD PA79074 ......................................................$12.95 Featherpro Featherboard AngleCube Bevel Gauge The FeatherPRO not only provides better protection against kickback, but also makes the infeed much smoother and easier than that of a rigid plastic feather board. Hardened, non-marring foam feathers provide up to 90 lbs of kickback resistance and will not harm carbide tip blades or router bits if contacted. If the feathers are damaged, they can be easily replaced FEATHERPRO FEATHERBOARD BP06096 ......................................................$29.95 REPLACE FEATHERS STANDARD BP06126 ......................................................$14.95 Table Saw Inserts Setting the angle of your table saw blade is very easy when using the AngleCube. Simply place the AngleCube on the table surface and press zero. Then attach the magnetized AngleCube on the saw blade to see the relative bevel angle between your blade and table top. The tilt range is between 0 and 90 degrees. The AngleCube now runs on a rechargeable battery and includes a usb charging cable. ANGLECUBE BEVEL GAUGE IP35226 ...$36.95 Zero clearance inserts are a very efficient way to tune up a table saw. Most US made inserts are made of one half inch high density phenolic resin and are completely flat. There are also four adjustment screws that will help you get the insert perfectly level in your table. Measurements are for table saw openings. Featherboard Stackable Kit Incra Miter Slides DELTA 3-3/4" x 13-3/8" LC10000 ...................$27.95 CRAFTSMAN 3-3/4" x 14" LC10001 ...............$27.95 JET & GENERAL 3-7/16" x 12-1/2" x 7/16" LC10002 ............................................................$27.95 POWERMATIC for 66 saw only LC10003 ......$27.95 POWERMATIC PM2000 w/slot LC10005 .......$39.95 DADO / POWERMATIC PM2000 wo/slot LC10006 ............................................................$39.95 DEWALT DW744 & DW746 LC10010.............$27.95 JET XACTA SAW LEFT LC10011...................$27.95 RIGID R4512 LC10013....................................$27.95 JET DELUXE XACTA SAW LC10014.............$32.95 RIGID R4512 (RG-6) LC10017........................$29.95 CRAFTSMAN 21833 LC10018........................$32.95 BOSCH 4000 SERIES w/slot LC10019...........$28.95 BOSCH 4000 SERIES wo/slot LC10020........$28.95 HITACHI / PORTER CABLE LC10021............$28.95 JET PROSHOP w/slot LC10022......................$29.95 JET PROSHOP wo/slot LC10023....................$29.95 The Featherduo is ideal for feeding taller material on table saws, band saws and router tables. Hardened, non-marring foam feathers provide up to 90 lbs of kickback resistance and will not harm carbide tip blades or router bits if contacted. If the feathers are damaged, they can be easily replaced. Includes two standard replacement feathers as a bonus. Hardware fits 3/4 miter track; also Includes 1/4*20 T slot hardware The Duo can be separated and used as two individual feather boards. FEATHERDUO STACKABLE FEATHERBOARD KIT BP06133 ..............$59.99 These miter sliders are the best way to make a variety of jigs. Each miter slider is machined perfectly to fit in a standard 3/8" x 3/4" miter track and is adjustable for a perfect, no slip fit. Included with each miter slider are plans to build a crosscut jig, tenoning jig and a featherboard. Each sold individually. INCRA MITER SLIDER 18" IMS-101 ................................................$16.95 24" IMS-102 ................................................$22.95 Order Online: www.woodworkingshop. com 53
Magnified View - Please use mouse to move page for easier readability