Machine Accessories GuidePro FencePro Featherboard Incra Miter Channel Works with INCRA Miter Sliders and INCRA Miter Gauges or any standard 3/8" by 3/4" miter bar. T-Slot design helps with hold down capability and they are made of hard anodized aluminum for durability. Mounts easily with pre-drilled holes and included fasteners. Cut a 1-1/8" wide by 1/2" deep groove in your application to fit the INCRA T-Slot Miter Channel. When installed, the Miter Channel should sit slightly below the surface of the table. Attach using the supplied fasteners. 32" INCRA MITER CHANNEL IN00032 ...$19.95 48" INCRA MITER CHANNEL IN00048 ...$25.95 FencePRO Featherboard protects you against kickback far better than plastic or wood feathers. EVA is a High Density closed cell material that is exceptionally durable and absorbs energy from kickback. Feathers are also shatterproof and unlike plastic feathers can be replaced if damaged. FencePRO offers benefits you simply cannot get with plastic or wooden feathers. Use FencePRO with our FeatherPRO featherboards for the ultimate in feed control and safety. FencePRO comes in a 2- pack for use separately or for stacking. FENCEPRO FEATHERBOARD 2PK BP06423.......................................................$39.99 GuidePRO is the ideal accessory for all band saw owners. Whether re-sawing dressed lumber or rougher pieces, the GuidePRO, with its flexible silicon feather, will maintain constant pressure between the work piece and the fence helping ensure the squarest cut possible. Just slide the GuidePRO into the miter slot, rotate it clockwise until it stops and push the GuidePRO against the work piece and fence with desired pressure, then press down the locking lever to secure the work piece. Be sure to keep the feather near the leading edge of the work for the cleanest cut. The GuidePRO Extension adds 4" of height to the GuidePRO and comes with a 10" feather. The GuidePRO Anchor Bar is used to adapt the GuidePRO to use on a router table or table saw. GUIDEPRO BAND SAW GUIDE BP06270 .......................................................$77.99 EXTENSION BP06287 ...................$19.99 3/4" ANCHOR BAR BP06294....................$24.99 Pushpro Push Stick Featherpro Featherboard Featherboard jig not included. AngleCube Bevel Gauge Featuring High Density Foam tips, PushPRO improves feed control, protects wood, reduces vibration on the hands and protects you and your tools in case of accidental contact between the Push Stick and the blade. PUSHPRO PUSH STICK BP06300 ..........$19.99 REPLACEMENT TIPS BP06324 .................$4.99 The FeatherPRO not only provides better protection against kickback, but also makes the infeed much smoother and easier than that of a rigid plastic feather board. Hardened, non-marring foam feathers provide up to 90 lbs of kickback resistance and will not harm carbide tip blades or router bits if contacted. If the feathers are damaged, they can be easily replaced FEATHERPRO FEATHERBOARD BP06096 ......................................................$29.95 REPLACE FEATHERS STANDARD BP06126 ......................................................$14.95 Miter Track Accessories RECTANGULAR NUTS 1/4-20 (10PK) PK13011 .......................$3.95 HEX HEAD BOLT 1/4-20 X 3" (10PK) PK13030 ............$2.95 Setting the angle of your table saw blade is very easy when using the AngleCube. Simply place the AngleCube on the table surface and press zero. Then attach the magnetized AngleCube on the saw blade to see the relative bevel angle between your blade and table top. The tilt range is between 0 and 90 degrees. The AngleCube now runs on a rechargeable battery and includes a usb charging cable. ANGLECUBE BEVEL GAUGE IP35226 ...$39.95 STEEL T-SLOT BOLTS 5/16"-18 - 10 PACK 1" WK48370................$6.95 1-1/2" WK48380..............$10.95 2-1/2" WK48390 .............$12.95 3-1/2" WK48400 .............$12.95 KNOB 5 PRONG 5/16"-18 WK48460 ................................$2.95 KNOB FOUR ARM 5/16"-18 WK48500 ................................$2.95 KNOB ERGO STYLE THRU HOLE 1/4"-20 WK48520...................$2.95 KNOB T-STYLE 5/16"-18 WK48840.......................................$3.95 KNOB FOUR ARM THRU HOLE 1/4"-20 WK48860 .......................$2.95 KNOB FOUR ARM THRU HOLE 5/16"-18 WK48870.......................$2.95 KNOB ERGO STYLE THRU HOLE 5/16"-18 WK48880 ...........$2.95 KNOB MINIATURE 10-24 STUD(2PK) WK48890.......................................$2.95 CAM ACTION HOLD DOWN 1/4 20 TPI WK45470 .....................................$9.95 Featherboard Stackable Kit Incra Miter Slides The Featherduo is ideal for feeding taller material on table saws, band saws and router tables. Hardened, non-marring foam feathers provide up to 90 lbs of kickback resistance and will not harm carbide tip blades or router bits if contacted. If the feathers are damaged, they can be easily replaced. Includes two standard replacement feathers as a bonus. Hardware fits 3/4 miter track; also Includes 1/4*20 T slot hardware The Duo can be separated and used as two individual feather boards. FEATHERDUO STACKABLE FEATHERBOARD KIT BP06133 ..............$59.99 These miter sliders are the best way to make a variety of jigs. Each miter slider is machined perfectly to fit in a standard 3/8" x 3/4" miter track and is adjustable for a perfect, no slip fit. Included with each miter slider are plans to build a crosscut jig, tenoning jig and a featherboard. Each sold individually. INCRA MITER SLIDER 18" IMS-101 ................................................$19.95 24" IMS-102 ................................................$24.95
Magnified View - Please use mouse to move page for easier readability